In April 2016 Manchester eScholar was replaced by the University of Manchester’s new Research Information Management System, Pure. In the autumn the University’s research outputs will be available to search and browse via a new Research Portal. Until then the University’s full publication record can be accessed via a temporary portal and the old eScholar content is available to search and browse via this archive.

Investigation of a novel multiresonant beam energy harvester and a complex conjugate matching circuit

Qi, Shaofan

[Thesis]. Manchester, UK: The University of Manchester; 2011.

Access to files

Abstract

The aim of the work described in this thesis is firstly to improve the collection of vibration energy for piezoelectric cantilever harvesters, by a mechanical technique, so that the devices can harvest energy over a wider bandwidth. Secondly to investigate a new circuit topology for achieving complex conjugate load matching to the piezoelectric harvester. The thesis has been divided into two parts – the mechanical approach and the electrical approach.For the mechanical approach, a novel multiresonant beam, comprising piezoelectric fiber composites on a clamped-clamped beam and side mounted cantilevers, was proposed. The side cantilevers are tuned by tip masses to be resonant at different frequencies. A Rayleigh-Ritz model was developed to predict the vibration response of the proposed model multiresonant beam. This model showed that the bandwidth of the multiresonant beam was increased over that of a single cantilever harvester.A multiresonant beam for energy harvesting was experimentally tested and compared with a single cantilever energy harvester. The transmissibility and voltage responses were investigated, the beam showed a wide frequency response between 14.5Hz and 31Hz, whereas the single cantilever only showed one resonant frequency. Therefore the multiresonant beam system is feasible for wide band energy harvesting.For the electrical approach, the task was to investigate complex conjugate impedance matching for the piezoelectric energy harvesters, so that the output impedance from the piezoelectric harvester can be reduced, and maximum energy extracted from the device with a possibility of frequency tuning. A new amplified inductor circuit was proposed to enable the capacitive output impedance of the piezoelectric device to be cancelled. Experimental and software simulations are provided to verify the theoretical predictions.A prototype amplified inductor circuit was simulated and tested. The results showed that a variable effective inductance was achieved. However the circuit is lossy due to imperfections within the system, and needs further work to eliminate these imperfections.

Bibliographic metadata

Type of resource:
Content type:
Form of thesis:
Type of submission:
Degree type:
Doctor of Philosophy
Degree programme:
PhD Electrical and Electronic Engineering
Publication date:
Location:
Manchester, UK
Total pages:
256
Abstract:
The aim of the work described in this thesis is firstly to improve the collection of vibration energy for piezoelectric cantilever harvesters, by a mechanical technique, so that the devices can harvest energy over a wider bandwidth. Secondly to investigate a new circuit topology for achieving complex conjugate load matching to the piezoelectric harvester. The thesis has been divided into two parts – the mechanical approach and the electrical approach.For the mechanical approach, a novel multiresonant beam, comprising piezoelectric fiber composites on a clamped-clamped beam and side mounted cantilevers, was proposed. The side cantilevers are tuned by tip masses to be resonant at different frequencies. A Rayleigh-Ritz model was developed to predict the vibration response of the proposed model multiresonant beam. This model showed that the bandwidth of the multiresonant beam was increased over that of a single cantilever harvester.A multiresonant beam for energy harvesting was experimentally tested and compared with a single cantilever energy harvester. The transmissibility and voltage responses were investigated, the beam showed a wide frequency response between 14.5Hz and 31Hz, whereas the single cantilever only showed one resonant frequency. Therefore the multiresonant beam system is feasible for wide band energy harvesting.For the electrical approach, the task was to investigate complex conjugate impedance matching for the piezoelectric energy harvesters, so that the output impedance from the piezoelectric harvester can be reduced, and maximum energy extracted from the device with a possibility of frequency tuning. A new amplified inductor circuit was proposed to enable the capacitive output impedance of the piezoelectric device to be cancelled. Experimental and software simulations are provided to verify the theoretical predictions.A prototype amplified inductor circuit was simulated and tested. The results showed that a variable effective inductance was achieved. However the circuit is lossy due to imperfections within the system, and needs further work to eliminate these imperfections.
Additional digital content not deposited electronically:
N/A
Non-digital content not deposited electronically:
N/A
Thesis main supervisor(s):
Thesis advisor(s):
Language:
en

Institutional metadata

University researcher(s):

Record metadata

Manchester eScholar ID:
uk-ac-man-scw:120197
Created by:
Qi, Shaofan
Created:
18th March, 2011, 15:25:06
Last modified by:
Qi, Shaofan
Last modified:
1st November, 2013, 14:17:37

Can we help?

The library chat service will be available from 11am-3pm Monday to Friday (excluding Bank Holidays). You can also email your enquiry to us.